Close filters
 
  •  
from to
1 From 2
No results were found for the filter!
Relay 4 Board
Relay 4 Board
Relay 4 Board is a cost effective solution for adding relays to your device. Single ULN2803 driver IC with 8 Darlington arrays drives each of the four available relays. Screw-terminals allow you clean and easy output relay connectivity,...
₹ 3,139.00 *
SmartPROTO Board
SmartPROTO Board
SmartPROTO board features female IDC10 connector and two prototyping areas which enable you place your own components and assemble an accessory board which can be connected with mikroElektronika development boards. First prototyping area...
₹ 519.00 *
VOLT - Smart USB Li-Po battery charger
VOLT - Smart USB Li-Po battery charger
VOLT is a smart USB Li-Polymer battery charger. It features power management circuitry with MCP73832 , which can charge the battery over USB connector. Using provided screw terminals (VSYS and GND) VOLT can also be used to power your...
₹ 1,459.00 *
Ethernet Connector Board
Ethernet Connector Board
Ethernet Connector Boards include a 10/100 Base-Transformer RJ45 connector that enables you to easily connect your prototype board to the Ethernet network. Ethernet Connector Board is a simple, yet effective solution for adding reliable...
₹ 1,039.00 *
Microphone AMP Board
Microphone AMP Board
The Microphone AMP Board enables you to add a power amplifier with microphone to your applications. There is an on-board Audio Power Amplifier LM4864 and microphone that can be connected to your prototype device via an on-board screw...
₹ 1,259.00 *
mikroProg to ICD2 & ICD3 adapter
mikroProg to ICD2 & ICD3 adapter
mikroProg to ICD2 & ICD3 is an adapter board which allows you to connect mikroProg™ programmer and In-Circuit debugger to target board where only ICD2/3 connector is available for programming. Board provides the necessary interface for...
₹ 529.00 *
Gesture Board USB Adapter
Gesture Board USB Adapter
This I2C to USB adapter is specifically built for connecting our Gesture Board to a PC, allowing you to explore the possibilities of Microchip's MGC3130 3D gesture recognition controller. The adapter is also available already paired with...
₹ 1,259.00 *
Bipolar Stepper Motor Driver Board
Bipolar Stepper Motor Driver Board
The Bipolar Stepper Motor Driver Board features a complete microstepping motor driver with a built-in translator A3967SLB . It is designed to operate bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output...
₹ 2,639.00 *
CANSPI Board
CANSPI Board
CANSPI Board is a CAN development tool for microcontrollers with SPI interface. The Board includes MCP2515 CAN controller and MCP2551 transceiver. It is capable of transmitting and receiving both standard and extended data and remote...
₹ 2,209.00 *
NFC USB Dongle
NFC USB Dongle
NFC USB Dongle is an NFC Reader-Writer based on NXP’s PN7150 high-performance full NFC controller, supporting all NFC Forum modes. The USB NFC Dongle is powered through USB connector. This NFC controller supports all NFC Forum...
₹ 3,049.00 *
TFT PROTO 5" Capacitive
TFT PROTO 5" Capacitive
TFT PROTO 5" Capacitive carries the 800x480 RVT50AQTNWC00 TFT screen. The SSD1963 display controller drives the TFT display, with a 1215K byte buffer that supports up to 864x480 at 24bpp displays. The touchpanel is driven by a FT5x06...
₹ 10,399.00 *
mikroDrive Board
mikroDrive Board
Board features a high-current Darlington arrays ULN2803AN suitable for interfacing between a low-level logic circuitry and multiple peripheral power loads. Typical power loads with over 260 W (350 mA x 8, 95V) may have drivers turned on...
₹ 1,889.00 *
1 From 2
Viewed