Close filters
 
  •  
  •  
from to
1 From 54
No results were found for the filter!
NEW
SparkFun Analog MEMS Microphone Breakout - SPH8878LR5H-1
SparkFun Analog MEMS Microphone Breakout -...
Description : The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the SPH8878LR5H-1 analog microphone from Knowles. This board features an OpAmp to bring the output of the microphone to a usable level, allowing you to...
₹ 769.00 *
MyoWare 2.0 Reference Cable
MyoWare 2.0 Reference Cable
The MyoWare® 2.0 Reference Cable is meant as an extension for the MyoWare 2.0 Muscle Sensor's reference pin. You will just need to insert the pin into its housing and place a biomedical sensor pad into the electrode snap. When ready,...
₹ 189.00 *
MyoWare 2.0 Power Shield
MyoWare 2.0 Power Shield
The MyoWare® 2.0 Power Shield is designed to easily power the MyoWare 2.0 Muscle Sensor for remote applications. The MyoWare Power Shield is equipped with snap connectors on the board so you can easily stack it to the top side of the...
₹ 2,199.00 *
MyoWare 2.0 Muscle Sensor
MyoWare 2.0 Muscle Sensor
Using our muscles to control things is the way that most of us are accustomed to doing it. We push buttons, pull levers, move joysticks... but what if we could take the buttons, levers and joysticks out of the equation and control it...
₹ 4,599.00 *
MyoWare 2.0 Arduino Shield
MyoWare 2.0 Arduino Shield
The MyoWare® 2.0 Arduino Shield is designed to easily connect up to six MyoWare 2.0 Muscle Sensors and Link Shields using 3.5mm TRS-to-TRS audio cables. The board comes pre-populated with male headers so all you would need to do is stack...
₹ 1,599.00 *
MyoWare 2.0 Link Shield
MyoWare 2.0 Link Shield
The MyoWare® 2.0 Link Shield is designed to easily connect a MyoWare 2.0 Muscle Sensor to your Arduino microcontroller. The shield provides a 3.5mm TRS jack so that you can use a 3.5mm TRS-to-TRS cable to link the boards together. The...
₹ 1,999.00 *
MyoWare 2.0 LED Shield
MyoWare 2.0 LED Shield
The MyoWare® 2.0 LED Shield is designed to display the magnitude of a target muscle's signal and power the MyoWare 2.0 Muscle Sensor with its built-in battery. The blue 10-segment bar graph shows the magnitude of the measured signal. The...
₹ 3,999.00 *
MyoWare 2.0 Cable Shield
MyoWare 2.0 Cable Shield
The MyoWare® 2.0 Muscle Sensor is designed to be wearable, allowing you to attach biomedical sensor pads directly to the board itself. However, there still may be cases where you want to mount the sensor pads away from the board; this is...
₹ 899.00 *
Tsunami Super WAV Trigger (Qwiic)
Tsunami Super WAV Trigger (Qwiic)
Based on a new generation ARM Cortex M7, the Qwiic Tsunami Super WAV Trigger extends polyphony to 32 mono or 18 stereo simultaneous uncompressed 44.1kHz, 16-bit tracks. Each track can start, pause, resume, loop and stop independently,...
₹ 9,449.00 *
SparkFun RFID Qwiic Kit
SparkFun RFID Qwiic Kit
The SparkFun RFID Qwiic Kit is a simple, yet all-in-one I 2 C based RFID starting point for the ID-3LA, ID-12LA, and ID-20LA readers. Simply plug a reader into the headers and use a Qwiic cable to connect to any Qwiic enabled development...
₹ 4,939.00 *
SparkFun Analog MEMS Microphone Breakout - ICS-40180
SparkFun Analog MEMS Microphone Breakout -...
The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the InvenSense ICS-40180 analog microphone. This board features an OpAmp to bring the output of the microphone to a usable level, allowing you to plug directly into...
₹ 769.00 *
SparkFun USB LiPoly Charger - Single Cell
SparkFun USB LiPoly Charger - Single Cell
If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The SparkFun USB LiPo Charger is a basic charging circuit that allows you to charge 3.7V LiPo cells at a rate of 500mA or 100mA. It is designed...
₹ 1,849.00 *
1 From 54
Viewed