RS485 2 click

Please inform me as soon as the product is available again.
₹ 1,889.00 *

Prices incl. GST

Out of Stock.

  • MIKROE-2700
  • MIKROE-2700
RS485 2 click  carries the  MAX3471  half-duplex transceiver intended for...more
Product information "RS485 2 click"
RS485 2 click carries the MAX3471 half-duplex transceiver intended for lithium battery-powered RS-485/RS-422 applications. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over UART interface with additional functionality provided by the following pins on the mikroBUS™ line: PWM, CS.

MAX3471 transceiver features

The MAX3471 draws only 1.6µA (typical) supply current from a 3.6V supply with the receiver enabled and the driver disabled. Its wide 2.5V to 5.5V supply voltage guarantees operation over the lifetime of a lithium battery. 

This device contains one driver and one receiver. Its true fail-safe receiver input guarantees a logic-high receiver output when the receiver inputs are open or shorted, or when they are connected to a terminated transmission line with all drivers disabled. 

The MAX3471 receiver operates at up to 64kbps and incorporates input filtering in addition to input hysteresis. This filtering enhances noise immunity when differential signals have very slow rise and fall times.

How the click works

There are two pairs of screw terminals on board the RS485 2 click. The ones marked with A and B are differential high and differential low communication lines. We added two more terminals for VCC and GND reference if needed for further interfacing.

Specifications

Type RS485
Applications Battery-Powered Differential Communications
On-board modules MAX3471 half-duplex transceiver
Key Features 1.6µA Supply Current with Receiver Enabled; intended for lithium battery-powered RS-485/RS-422 applications.
Input Voltage 3.3V or 5V
Click board size L (57.15 x 25.4 mm)

Pinout diagram

This table shows how the pinout on RS485 2 click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
  NC 1 AN PWM 16 RE Receiver output enable, active low
  NC 2 RST INT 15 NC  
Driver output enable, active high DE 3 CS TX 14 RX UART data receive 
  NC 4 SCK RX 13 TX UART data transmit
  NC 5 MISO SCL 12 NC  
  NC 6 MOSI SDA 11 NC  
Power supply +3.3V 7 3.3V 5V 10 +5V Power supply
Ground GND 8 GND GND 9 GND Ground

Jumpers and settings

Designator Name Default Position Default Option Description
JP1 VCC SEL Left 3V3 Power Supply Voltage Selection 3V3/5V, left position 3V3, right position 5V

Programming

Code examples for RS485 2 click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

The following code snippet shows a part of the RS485 2 click example. One device is set as the slave, and the other is the master. Upon button press on the master, an LED light on the slave device will change its state.

01 void main()
02 {
03     systemInit();
04
05    while( 1 )
06     {
07 #ifdef MASTER_NODE
08         if (isButtonPressed())
09         {
10             ledToggle();
11             RS485_2_transmit(&cmd, 1);
12         }
13         Delay_ms(25);
14 #endif
15     }
16 }
17
18 #ifdef SLAVE_NODE
19 void RX_ISR() iv IVT_INT_USART3 ics ICS_AUTO
20 {
21     if( RXNE_USART3_SR_bit )
22     {
23         char rxByte = USART3_DR;
24
25        if (rxByte == ON_CMD)
26         {
27             LED_PIN = LED_ON;
28         }
29         else if (rxByte == OFF_CMD)
30         {
31             LED_PIN = LED_OFF;
32         }
33     }
34 }

Downloads

 mikroBUS™ Standard specification 
 MAX3471 datasheet
 RS485 2 click schematic

 LibStock: RS485 2 click library

Related links to "RS485 2 click"
Read, write and discuss reviews...more
Customer evaluation for "RS485 2 click"
Write a review
Reviews will be activated after verification.

The fields marked with * are required.

Viewed