BIG 7-SEG R click

Please inform me as soon as the product is available again.
₹ 1,999.00 *

Prices incl. GST

Out of Stock.

  • MIKROE-2269
  • MIKROE-2269
BIG 7-SEG R click  is what you need if you want to add a seven-segment LED display to your...more
Product information "BIG 7-SEG R click"

BIG 7-SEG R click is what you need if you want to add a seven-segment LED display to your project. This click features an SC10-21SRWA seven-segment display. Communication between the MCU and the SC10-21SRWA display is established via serial-IN, parallel-OUT shift register 74HC595 IC.

The click runs on either 3.3V of 5V power supply and communicates with the target MCU over an SPI interface.

Display

The click displays letters, numbers and symbols in highly readable form. It can be used in any simple interface and combined with other click boards. The color of the displayed character is red, as the R in the name of the click states.

Light intensity

The light intensity on the display is controlled via the PWM pin on the board.

Applications

Adding a seven-segment LED display to your device with SPI interface.

Specifications

Type LED Segment
Applications Adding a seven-segment LED display to your device with SPI interface
On-board modules SC10-21SRWA seven-segment display, parallel-OUT shift register 74HC595 IC
Key Features 1.0 inch digit height, Standard: grey face, white segment, Low current operation
Key Benefits Letters, numbers and symbols in highly readable form
Interface SPI,PWM,GPIO
Input Voltage 3.3V or 5V
Compatibility mikroBUS
Click board size L (57.15 x 25.4 mm)

Pinout diagram

This table shows how the pinout on BIG 7-SEG R click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

NotesPinMikrobus logo.pngPinNotes
  NC 1 AN PWM 16 PWM Display light intensity control
Master Reset for 74HC595 MR 2 RST INT 15 NC  
Latch for 74HC595 LAT 3 CS TX 14 NC  
Clock for 74HC595 CLK 4 SCK RX 13 NC  
Serial Data from 74HC595 to MCU DSO 5 MISO SCL 12 NC  
Serial Data from MCU to 74HC595 DSI 6 MOSI SDA 11 NC  
Data line when interfaced with 3.3V MCU 3.3V 7 +3.3V +5V 10 5V Data line when interfaced with 5V MCU and also power supply pin for display and the whole click hardware
Ground GND 8 GND GND 9 GND Ground

Jumpers and settings

Information about onboard jumpers:

DesignatorNameDefault PositionDefault OptionDescription: describe the use + list all options with respective descriptions
JP1 Logic level Left 3.3V Logic Level Selection toward host mcu 3.3V/5V, left position 3.3V, right position 5V

Programming

This demo is using BIG 7-SEG R click board to display characters in an endless loop, with fixed time interval whilst changing its PWM duty.

  • Operating Voltage Range: 2.0 to 6.0 V
  • Operating Temperature: – 55 to 125 C

This example for STM32F107VC MCU ( EasyMx PRO v7 for ARM ), resets and initializes the BIG 7-SEG R click board takes characters from the static array and displays them while changing PWM duty cycle, all in an endless loop.

 1   extern char dig_array[MAX_CHARACTERS];
2
3   // Variables
4   unsigned short counter;
5   unsigned int luminosity;
6   unsigned int pwm_period;
7   int8_t valid;
8
9   char demo_array[20] =
10   { 'M', 'I', 'K', 'R', 'O',
11     'E', 'L', 'E', 'K', 'T', 'R', 'O', 'N', 'I', 'K', 'A',
12     '2', '0', '1', '6'
13   };
14
15   void main()
16   {
17    // MCU Init
18    GPIO_Digital_Output(&GPIOD_ODR, _GPIO_PINMASK_13);     // Set PORTD.B13 as digital input
19    GPIO_Digital_Output(&GPIOC_ODR, _GPIO_PINMASK_2);      // Set PORTC.B2 as digital output
20
21    // SPI Init
22    SPI3_Init_Advanced( _SPI_FPCLK_DIV16, _SPI_MASTER | _SPI_8_BIT |
23   _SPI_CLK_IDLE_LOW | _SPI_FIRST_CLK_EDGE_TRANSITION |
24   _SPI_MSB_FIRST | _SPI_SS_DISABLE | _SPI_SSM_ENABLE |
25   _SPI_SSI_1, &_GPIO_MODULE_SPI3_PC10_11_12 );
26
27    // PWM Init
28    pwm_period = PWM_TIM5_Init(5000);                      // PWM Init on 5kHz
29    PWM_TIM5_Set_Duty(100, _PWM_NON_INVERTED, _PWM_CHANNEL1);
30    PWM_TIM5_Start(_PWM_CHANNEL1, &_GPIO_MODULE_TIM5_CH1_PA0);
31
32    // 74HC595 Init
33    HC595_LAT = 0;
34    HC595_RES = 0;
35    HC595_reset();
36
37    // Init counter and segment luminosity
38    counter = 0;
39    luminosity = 0;
40
41    // Endless loop
42    while (1)
43     {
44      valid = seg_7_display(demo_array[counter]);
45      PWM_TIM5_Set_Duty(100 + luminosity, _PWM_NON_INVERTED, _PWM_CHANNEL1);
46      delay_ms(750);
47      luminosity += 100;
48      counter++;
49      if (counter == 20)
50        counter = 0;
51      if (luminosity == 4000)
52        luminosity = 0;
53     }
54   }

 

Related links to "BIG 7-SEG R click"
Read, write and discuss reviews...more
Customer evaluation for "BIG 7-SEG R click"
Write a review
Reviews will be activated after verification.

The fields marked with * are required.

Viewed