6LoWPAN C click

Please inform me as soon as the product is available again.
₹ 2,729.00 *

Prices incl. GST

Out of Stock.

  • MIKROE-2219
  • MIKROE-2219
6LoWPAN C click  carries the  CC2520  2.4GHz RF transceiver. The click is...more
Product information "6LoWPAN C click"

6LoWPAN C click carries the CC2520 2.4GHz RF transceiver. The click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over SPI interface, with additional functionality provided by the following pins on the mikroBUS™ line: PWM, INT, RST, AN.

CC2520 features

The CC2520 is TI's second-generation ZigBee®/IEEE 802.15.4 RF transceiver for the 2.4GHz unlicensed ISM band. This chip enables industrial grade applications by offering state-of-the-art selectivity/co-existence, excellent link budget, operation up to 125°C and low voltage operation.

In addition, the CC2520 provides extensive hardware support for frame handling, data buffering, burst transmissions, data encryption, data authentication, clear channel assessment, link quality indication and frame timing information.

Antenna features

The antenna is intended for use with all 2.4 GHz applications. It uses a ground plane in order to radiate efficiently, but this ground plane must not extend underneath the antenna itself.

Specifications

Type RF 2.4GHz
Applications IEEE 802.15.4 systems, ZigBee® systems, industrial monitoring and control, home and building automation, Automatic Meter Reading, Low-power wireless sensor networks, etc.
On-board modules CC2520
Key Features 2.4GHz SMD antenna
Interface SPI,GPIO
Input Voltage 3.3V
Compatibility mikroBUS
Click board size S (28.6 x 25.4 mm)

Pinout diagram

This table shows how the pinout on 6LowPAN C click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

NotesPinMikrobus logo.pngPinNotes
General purpose digital I/O RF GPIO0 1 AN PWM 16 RF VREG EN When high, digital voltage regulator is active
External reset pin, active low RF RST# 2 RST INT 15 RF GPIO 1 General purpose digital I/O
Chip select RF CS 3 CS TX 14 NC  
Serial clock RF SCK 4 SCK RX 13 NC  
Master input slave output RF MISO 5 MISO SCL 12 NC  
Master output slave input RF MOSI 6 MOSI SDA 11 NC  
Power supply +3.3V 7 3.3V 5V 10 NC  
Ground GND 8 GND GND 9 GND Ground

Programming

Code examples for 6LoWPAN C click, written for MikroElektronika hardware and compilers are available on Libstock.

Note: The full 6LoWPAN stack is not currently implemented in our libraries. However, there are functionalities for sending and receiving data packets, as well as for setting the network ID and 16-bit addresses for individual devices. 

Code snippet

This code snippet, taken from our 6LoWPAN Click example for clicker 2 for MSP432, shows how data is transmitted and received between two MCUs using 6LoWPAN clicks.

The value of _RECEIVER_ determines whether the MCU will behave as a receiver or a transmitter. RF channel, PAN ID, and individual addresses are also defined.

There is an interrupt routine for detecting a button press, which is used in the transmitter code to indicate that a package should be sent.

The other interrupt routine is connected to the GP1 line of the click itself and will trigger when new data is ready to be received. It will check the received package, and turn on the data ready indicator if everything is fine.

In the main routine, after some initialization code, two sections can be found - one for the receiver and the other one for the transmitter.

The receiver will check the package ready indicator and handle the received package. In this example, an LED will be toggled to indicate successful data transfer.

The transmitter will wait for a flag to be set from the button interrupt routine. When the flag is set, a package will be sent to the receiver.

01 #if RECEIVER
02     // Initialize BasicRF
03     config.myAddr = LIGHT_ADDR;
04     if (C6LP_init(&config) == FAILED)
05         LED1 = 1;
06
07     C6LP_receiveOn();
08     EnableInterrupts();
09
10     while (1)
11     {
12         while (!C6LP_isPacketReady());
13
14         if (C6LP_receive(pRxData, APP_PAYLOAD_LENGTH, 0) > 0)
15         {
16             if (pRxData[0] == LIGHT_TOGGLE_CMD)
17             {
18                 LED0 = !LED0;
19             }
20         }
21     }
22 #else
23     pTxData[0] = LIGHT_TOGGLE_CMD;
24
25     // Initialize BasicRF
26     config.myAddr = SWITCH_ADDR;
27     if (C6LP_init(&config) == FAILED)
28         LED1 = 1;
29
30     // Keep Receiver off when not needed to save power
31     C6LP_receiveOff();
32
33     flag = 0;
34     EnableInterrupts();
35     while (1)
36     {
37         if (flag)
38         {
39             flag = 0;
40             LED0 = !LED0;
41             C6LP_sendPacket(LIGHT_ADDR, pTxData, APP_PAYLOAD_LENGTH);
42             EnableInterrupts();
43         }
44     }
45 #endif

 

Related links to "6LoWPAN C click"
Read, write and discuss reviews...more
Customer evaluation for "6LoWPAN C click"
Write a review
Reviews will be activated after verification.

The fields marked with * are required.

Viewed