GSM Click

Please inform me as soon as the product is available again.
₹ 5,149.00 *

Prices incl. GST

Out of Stock.

  • MIKROE-1298
  • MIKROE-1298
  Precision control GSM click is the easiest way to add GSM/GPRS communication to...more
Product information "GSM Click"

 

Precision control

GSM click is the easiest way to add GSM/GPRS communication to your device. The click features Telit's GL865-QUAD module. GSM click runs either on 3.3V or 5V power supply and communicates with the target microcontroller via UART interface.

Python Script Interpreter

It is possible to run an application from inside the module via the embedded Python Script Interpreter. Python is an easy-to-use programming language with clear syntax, and an interface that makes it simple to test small snippets of code.

Quad-band coverage

The module has worldwide coverage - 850/900/1800/1900 MHz frequencies. GSM supports incoming and outgoing voice calls, sms and data communication (via GPRS)

Power saving modes

In power saving mode, the GL865-QUAD uses around 1.5 mA, and in power off mode it uses less than 5 μA. That is considerably low and ideal for IoT devices that rely on long battery life and low power consumption.

Phonebook

The Phonebook function allows storing of telephone numbers in the SIM memory. The capability of the Phonebook depends on the SIM version and its embedded memory. The SIM card socket is located at the back side of the click board.

Additional information about the GSM click

GSM click contains TXB0106 6-bit bidirectional voltage-level translator, for interfacing components that operate on different voltages from one another.

On-board SMA antenna connector as well as 3.5mm quadrupole earphone/microphone jack.

An onboard jumper (J1) is used to switch between 3.3V and 5V I/O voltage levels; by default, it's soldered in the 3.3V position.

Applications

Remote monitoring automation, asset tracking, surveillance and security, home automation systems, point of sales terminals etc.

Specification

Type GSM
Applications GSM click with it’s Telit GL865-QUAD IC is ideal for mobile devices.
On-board modules Telit GL865-QUAD GSM/GPRS
Key Features On-board antenna connector as well as 3.5mm quadrupole earphone/microphone jack. SIM card socket integrated at the bottom side of the board.
Key Benefits Supports GSM/GPRS 850/900/1800/ 1900 MHz Quad-band frequency. Supports GSM/GPRS protocol stack 3GPP.
Interface GPIO,UART
Input Voltage 3.3V or 5V
Compatibility mikroBUS
Click board size L (57.15 x 25.4 mm)

Key features

  • GL865-QUAD from Telit
    • Quad-band GSM | GPRS 850 / 900 / 1800 / 1900 MHz
    • TCP/IP protocol stack
    • integrated 3GPP protocol stack
    • Power consumption in power off mode: 5μA
    • Sensitivity:
      • 108 dBm (typ.) @ 850/900 MHz
      • 107 dBm (typ.) @ 1800/1900 MHz
  • TXB0106 voltage-level translator
  • Phyton Script Interpreter
  • Interface: RX, TX, INT, PWM, CS, RST and AN pin
  • Either 3.3V or 5V power supply

Pinout diagram

This table shows how the pinout on GSM click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

NotesPinMikrobus logo.png

mikroBUStm

PinNotes
Power ON monitor PWRMON 1 AN PWM 16 GPIO2 Jammer Detect Report
External SIM signal – Reset RST 2 RST INT 15 CTS Output for Clear to send signal
Input for Request to send signal RTS 3 CS TX 14 RXD Serial data input (TXD) from DTE
Not connected NC 4 SCK RX 13 TXD Serial data output to DTE
Not connected NC 5 MISO SCL 12 NC Not connected
Not connected NC 6 MOSI SDA 11 NC Not connected
Power supply +3.3V 7 3.3V 5V 10 +5V Power supply
Ground GND 8 GND GND 9 GND Ground

Programming

The following code snippet shows how the GSM engine is initialized. The function calls the initialization of AT adapter, timer and parser. This should be done before executing any other function.

 1 void GSM_init( void )
2 {
3     engine_init( gsm_default_handler );
4     hal_gsm_pwr( 0 );
5     Delay_ms( 100 );
6     hal_gsm_pwr( 1 );
7     Delay_ms( 2500 );
8     hal_gsm_pwr( 0 );
9
10     at_cmd( "AT" );
11     at_cmd( "AT+CSCS="GSM"" );
12     at_cmd( "AT+CMGF=1" );
13 }
Related links to "GSM Click"
Read, write and discuss reviews...more
Customer evaluation for "GSM Click"
Write a review
Reviews will be activated after verification.

The fields marked with * are required.

Viewed